What did you do to your jeep today? (2024)

moved my windshield washer bottle from the lower passanger wheel well, up into the engine bay, and trimmed some more plastic wheel liner...

You must be registered for see images

there are 2 metal weights on the bottle right now, as i had to cut the filler neck, and plastic weld it back together (so i can still use the cap)

this is all in hopes of installing a non liberty winch bumper on the front to start using my winch/compressor

CzarKJ said:

Sounds like it fell while it was there and they put it back in place haha

Click to expand...

Maybe. Hard to tell. Either way, I don't think I could pin it on them since they didn't do any work on the door.

I got it all pulled out and will have to wait for the repair kit to arrive.

Moabs

I Just got back from picking up a pristine set of 5 MOAB wheels off of an 05 Rubicon with 50%tread 245/75 Goodyear Fortera tires on them for only $500. Craigslist pulled through in the clutch. Folded down the rear seats and hauled them back in the Liberty.(flagusa)
:emoticondancer:

Got new wheels and tires on the 03 Green Jeep

You must be registered for see images attach

:icon_lol::icon_lol::ROFLJest:

LEDs for every single light in my tail light housing. Load resistors for the signals.

https://dl.dropboxusercontent.com/u/44657444/2016-02-23 12.49.57.mov

tommudd said:

Got new wheels and tires on the 03 Green Jeep
:icon_lol::icon_lol::ROFLJest:

Click to expand...

Ha ha...Nice wheels & Tires!!
I had to tow the Ram home..:icon_lol: :gr_grin:
55412[/ATTACH]"]

You must be registered for see images attach

sota said:

where did you get those? I'm intrigued.

Click to expand...

The KJ & Ram came from a local store many years ago, they had one on shelf, had to buy it!
Tom has a nice little collection including the New Bright.
I got so many now... I need an 18 wheeler to load them into!! :icon_lol:
55425[/ATTACH]"]

You must be registered for see images attach

Many come from Ebay etc..Here is a link from 2010: http://www.jeepkj.com/forum/f195/wanted-1-18th-scale-jeep-liberty-46880/
I also have flipped out recently on Jeep watches! Link: http://www.jeepkj.com/forum/f197/does-your-jeep-dealer-carry-apparel-acessories-57257/index2.html :gr_grin:
BTW here is a nice Red Fast Lane Remote controlled KJ Up for sale right now on ebay, make an offer!
http://www.ebay.com/itm/Fast-Lane-Jeep-Liberty-Remote-Controlled-Car-RC-Working-Battery-Charger-Remote-/231566178232

dude1116 said:

LEDs for every single light in my tail light housing. Load resistors for the signals.

Click to expand...

Can you share any additional details? Where'd you get them? Installation particulars? How-to on the resistors?

Thanks.

Jim McClain said:

Can you share any additional details? Where'd you get them? Installation particulars? How-to on the resistors?

Thanks.

Click to expand...

Pretty easy actually. I bought all of the LED bulbs from Superbright LEDs.

The only thing I don't like is that they're all Chinese bulbs. But at this point...what isn't made in China?? :shrug:

Anyway SBL has some instructions for their load resistors on their site and they come with them when you buy them. I only used these for the signals to stop the hyperflashing. The other two bulbs (Brake/running and reverse) were simple plug and play.

Pretty simple. They gave me splice connectors. Connect one splice connector to each end of the load resistor, and connect each splice connector to the positive/negative wires on the Jeep for the signal.

That being said...I have aftermarket tail lights with a wire loom that comes out of the back of the tail light. I actually used THESE wires to connect the load resistor so I didn't have to find out which wires were the equivalent on the Jeep wiring harness.

I drilled two holes small holes in the jeep on each side to mount the resistors behind the tail light with a couple of small sheet metal screws. (Spray painted the spots too to prevent rust)

Here are the resistors:

https://www.superbrightleds.com/mor...-turn-signal-hyper-flash-warning-fix/190/831/

And here are the instructions:

https://d114hh0cykhyb0.cloudfront.net/pdfs/LoadResistorBW-01.pdf

renegade 04 said:

I finally got a chance to install my OME lift kit. During the lift install the libby got new front upper control arms, new CV axles, new front sway bar links, also teraflex bump stops.That was back around Christmas, and now I noticed that my rear tri link is totally shoot and will need to replaced asap. I just want to say THANK YOU to this forum for all the helpful information. I may have taken my a week to install the lift, but it was one of the funnest weeks I have ever had. I will post before and after pics when it stops raining.

Click to expand...

Glad you had fun installing the lift
I always do !

You must be registered for see images

You must be registered for see images

You must be registered for see images

You must be registered for see images

You must be registered for see images

You must be registered for see images

Meet the design for the new vehicle storage house. I think i'm very close to building several of these this summer. Pretty much have the design locked down. Now i'm thinking about drawing up the assembly scaffolding and panel making jigs that'll help make this thing happen.

You must be registered for see images

Time to start cutting